To use the Eero Wi-Fi system fully, you have to replace your current router with Eero. If your present router supports all advanced features then, you can use Euro by just putting in the bridge mode. This will allow you to use your Current router and Eero will act as Range Extender Wi-Fi.
Here’s how you can put the Eero into Bridge Mode:
When Eero is in bridge mode, you still have to maintain the separate mesh Wi-Fi network which is being set up on it. Many features are not available like putting limits on internet access for specific family members, port forwarding’s setup process, even interfering with some advanced features is restricted.
When Eero is in Bridge mode, it only acts as a mesh extender for your present network.
Now, to enable Bridge mode, launch the Eero app on your phone, and in the top-right corner of the screen, tap on its Menu.
Select “Network Settings”.
Look for “Advanced Settings” at the bottom.
Now, the Eero system requires Reboot, after doing that it will be in Bridge Mode.
Now, the Euro system will provide you a basic mesh Wi-Fi network to which you can connect anytime and you can also change your advance settings using your current router. If you need further help or assistance, you can contact experts.
With the advent of smart home gadgets and the need for seamless home internet connectivity, individuals around the world are adopting mesh routers like Eero as the solution to this rising need. One company that has been at the forefront of the mesh router renaissance since 2016 is the Eero Company famed for its provision of the world’s first home Wi-Fi system. But, if you already own a router, can the product still work with it?
Eero can work with other routers. While Eero was created to replace existing routers, users can still link their other routers with an Eero. If you decide to use your Eero with other routers, you will need to put your Eero or existing router into a bridge mode or make a double NAT connection.
In the following sections, you’ll learn more about Eero routers and how to set up your Eero router to work with other routers.
How to Setup Your Eero with Other Routers
While experts at Eero recommend that users replace their existing routers with an Eero Wi-Fi system, it is still very possible for you to use your other routers alongside an Eero.
Setting up a bridge mode between both routers and making a double NAT connection are currently the two sure methods to set up your Eero Wi-Fi system with other routers.
Bridging Your Eero with Other Routers
If you’re planning to use your Eero with other routers, your first option is to create a bridge connection between your Eero router and your existing router. A typical bridge mode will require you to allow your dedicated upstream router to control the connection between your network and ISP.
There are several situations where bridging your Eero router may be your best option.
- Your network provider requires a PPPoE
- Your ISP requires that you use a specific MAC address that matches their equipment
- You use an AT&T U-verse provider
However, making a bridge connection with your Eero Wi-Fi system may cause you to lose some advanced features.
Before you bridge your Eero router, you must know that bridging your Eero will turn off its network service, but your Eero can still provide you with Wi-Fi access. More importantly, you will lack the ability to control your Eero network advanced feature via the Eero app once your Eero is on bridge mode.
Below is the step-by-step process to bridge your Eero with other routers:
- Launch your Eero app and tap on the settings icon, which is located at the bottom right corner.
- Click on Advanced.
- Click on the DHCP & NAT icon.
- Change your selection from the recommend Automatic to Bridge or Manual.
- At the top right corner of your app interface, click on the save icon.
By using your modem/router combo system in a bridge mode, you are altering its Wi-Fi abilities and transferring its internet network connection to your Eero Wi-Fi system. You can learn more bridging your modem/router combo device here.
How to Double NAT Your Eero
Another method to make your Eero work with other routers is to do a setup known as “Double NAT-ing.” While the double NAT-ing process may seem complicated, it is quite easy to implement.
There are no specific instructions for double NAT-ing your Eero with another router besides what’s offered in the app after you connect. With that said, below are several key things to note about double NAT-ing your Eero, according to Eero’s help page on Twitter:
- When Double NAT-ing your Eero with other routers, do not plug in your gateway Eero router directly into your modem, as shown in the Eero app. Instead, you should connect your gateway Eero into the other router. After connecting your gateway Eero to your existing router, you should follow the detailed steps in the Eero app.
- If you have or are using a modem/router combo system, connect your gateway Eero into the combo device and follow the instructions stated in the Eero app. (You can also use your modem/router combo device in bridge mode with your Eero. This allows you to use your modem/router combo device as a modem only.
- Most importantly, when double NAT-ing your Eero router, use an SSID and password on your Eero network system that is different from the one on your existing network. Running both networks with the same SSID and password will lead to network and other technical problems.
With the continuous development of smart home devices, there is also an increasing drive for a super-fast internet connection to make these smart home gadgets work seamlessly. From streaming 4K videos on the patio to faster download times, the Eero Home Wi-Fi system (consisting of the Eero, Eero Beacon, and the Google.
With Amazon’s purchase of the Eero brand in 2019, we can only hope for a super-secure, faster, and more affordable Wi-Fi connection with excellent home coverage soon.
I have a question regarding handoff between eeros while in bridge mode. here's my proposed network topology. Please let me know if this will work as anticipated.
let's say that a 3 pack of eero pro 6 nodes are switched to "bridge mode". Then, the nodes are interconnected with a wired backhaul to a TP link AX11000 MU-MIMO Tri-Band Gaming Router. the tp link serves as the router and the eeros are in bridge mode. Now let's say a client device moves far away from the TP link router and gets close to eero node #2. will the client device be seamlessly handed off to eero node #2?
By the way, I no longer want to use eero as a router because your adblocking feature is way too aggressive. Even when I switch off the ad blocking feature and eero secure features, eero still blocks a ton of websites.
You will not hand-off between TP-Link and the Eeros.
If you want to use eeros for Wifi with a TP-Link router you should disable the wireless in the TP-Link.
NOTE: As /u/opticspipe wrote if you have disabled eero secure the eero won't block a thing. That doesn't mean there isn't something else in the path that isn't blocking it but it won't be the eero.
u/heklakatla what do you think is blocking access while browsing? there is no issue when using a mobile network on the same browser, for any device. and while browsing with that TP-link router instead of the eeros, pages aren't being blocked.
As seamless as ever, so like kinda?
Eero is better at wifi than at being a router so bridged is still probably a good idea.
When you turn off the features you mention, it doesn’t block anything.
You still need to have one eero ahead of the other two in the topology, so you can’t just plug three of them into a router.
Seamless handoffs typically work just fine in bridge mode.
Bridging applies to if the eero is acting as a router or not. An eero network never “extends” another wireless network.
Interesting question, so I just did a test. My initial impression was that yes, if in bridge mode the Eeros should "roam" and act like access points, but it appears they do not.
I have an Omada router set up (dual WAN) with three TP-Link Deco's (two X60's and an X20) set up in Access Point mode. Interestingly, on the Deco app, there's "Router" and "AP mode. The Decos do appear to act like true AP's while in AP mode, and interestingly you can connect them to your main router in parallel in this mode (in other words there doesn't have to be a gateway with other decos downstream of it), as must be the case in Router mode for the Deco, or with Eero in any mode.
I just added an eero 6 router connected to a switch which is connected to the Omada router. I changed it to Bridge mode after setup. SSID and password are the same as with the Deco units. I immediately got a pop-up box in the eero app stating the following:
"Turn off your old Network" and "Keeping two networks with the same name and password causes problems for your wifi devices".
As of now, nothing is automatically moving over to the Eero, even though it's closer to several clients than the nearest Deco. Even my phone sitting right next to the Eero did roam – to another Deco, in another room. Only way I could make a device associate was to turn its wifi off and then back on. I did see a Nest device pop up, and then saw it was a Nest Detect smoke alarm which is normally "offline" and probably just authenticated to check in – it wasn't a real roaming event.
Strangely, a handful of wired devices do show up as "connected" in the Eero app even though none of them are downstream of the Eero router. No wifi devices connect automatically or appear to roam to it.
So no, appears Eero nodes will NOT act as AP's and allow roaming to & from other non-Eero nodes.
What is Bridge Mode on a Router?_
If you are experimenting with the various advanced features of your wireless network, you may wonder what is the bridge mode on a router. The best routers, after all, can successfully integrate this bridge functionality. So what is a bridge mode, what does it do, and why should you use it? Keep reading to find out.
- Bridging together two routers means that the secondary WiFi router becomes an extension of the primary WiFi router, for increased router functionality and better Internet connections.
- This is primarily done to increase the range of your wireless network if you notice dead spots throughout your home or office while using connected devices.
- Other advantages to bridging two routers are increased efficiency and increased maximum bandwidth. This also reduces any potential address conflict.
What Does Bridging a Router Do?
If you are learning how to set up a modem and router combo, or a standalone router, you should also learn about bridging. Simply put, bridge mode is a networking feature that ties two routers together.
Want to increase your range without bridge mode? Try a wireless range extender or a mesh network.
Benefits of Bridge Mode
There are a couple of key advantages to enabling bridge mode.
If you recently learned the definition of 5G on a router, you also know that the 5GHz band offers increased speed over the 2.4GHz band but decreased range. To get both speed and range, you can bridge together two routers. Once two routers are bridged, the secondary router acts as a wireless connection point to your overall network. Both routers will share the same IP address, which is handy. Without bridging, this secondary router will just be an access point for a new network.
Increase Maximum Bandwidth
In addition to offering increased range, bridging together two routers will increase the overall bandwidth of your wireless network. Routers have a maximum bandwidth limit and as you approach it, your speed and results will suffer. Bridging two routers effectively double this bandwidth limit, so feel free to connect dozens of mobile devices, computers, and smart appliances.
As previously mentioned, bridging together multiple routers increases your maximum range and your maximum bandwidth. Together, this results in an increase in efficiency throughout your network. There will be no contaminated connections, being as how both routers share the same public IP address, and the uptick in bandwidth means your network will never become clogged due to multiple devices being connected at once.
Both bridged routers not only share a static IP address, but any other settings you make to the primary router. In other words, you will only have to go in and make necessary changes to this primary router, and not the secondary “bridged” router. This includes security settings, port forwarding adjustments, parental controls, banned devices, and more.
Where to find your model number?
Look on the exterior of your device for the model number or use a mobile device to perform a web search. For ISP-supplied routers, contact your Internet service provider.
What are the disadvantages to bridge mode?
Putting a router in bridge mode will hamper some of the functionalities of the secondary, bridged, router. One router capability that is hampered is the ability to create a private network. The secondary router’s built-in NAT capabilities will also be reduced.
How to enable bridge mode?
This will vary depending on the makes and models of your routers, but always needs an Ethernet cable, available Ethernet ports, and Internet access for access to the web browser address bar.
STAT: In computer networking, the process of Network Address Translation (NAT) involves re-writing the source and/or destination address of IP packets as they pass through a router. NAT allows multiple hosts on a private network to access the internet using a single public IP address. (source)
Also, check to ensure you aren’t losing any features you want. Most mesh networks rely on serving as a router to provide some of their features, so scrutinize their documentation. For example, here are Eero’s unavailable features in bridge mode.
Connect your "gateway" or "network" node to your router and follow the configuration instructions. You will be prompted to put your gateway into "bridge mode." This mode disables any router functions in the gateway.
If you do not see a configuration screen, bridge mode will be under your device's app's "advanced networking" tab. In Google Home, for example, it's available under Wi-Fi > Settings > Advanced Networking > Network Mode.
Place your nodes and follow the configuration instructions in the app.
How to Add a Mesh Network to an Existing Router/Modem
If your modem has a router built into it, and you only want to use the modem part of it, you can instead turn off the router inside your modem and use the mesh network instead.
Disconnect any Ethernet cables from your router/modem. It will reduce demands on the router and prevent signal interruptions.
Open your combined modem/router's web portal or management app and enable "bridge mode." You may need to check your device's documentation, but this is generally found under "Wireless Settings" or in a similar area.
If you’re renting a device from your internet service provider, you may need to contact customer service and have them do this remotely.
If your router doesn’t automatically reboot, manually reboot it.
Connect your mesh network device and follow the configuration instructions provided in the app.
Can You Add A Mesh Network to an Existing Router?
Adding mesh networks to an existing router is possible, but it may not be the best option. In most situations, you’re probably better off removing or disabling your current router, yet if you need to keep it, you can still use mesh networks.
Traditional routers have an area of effectiveness; think of them like a radio station, where the further away you get, the weaker the signal becomes. This signal can be pushed further with Wi-Fi extenders, but it still has a range that fades.
Mesh networks work by placing “nodes” around a space, with one node connected to your modem to serve as a router. As you go around your area, the nodes stay in contact with your device and each other, maintaining a signal at a higher strength. As long you place the nodes strategically, you’ll have a connection.
When you combine the two, you risk “double NAT,” short for double Network Address Translation. Essentially, your mesh network and traditional router fight over who gets to direct your internet traffic. One of the two has to be disabled to prevent this from happening.
After connecting your modem, go to 192.168.1.254 and select Firewall > IP Passthrough, enter the access code from the sticker on your ATT modem and change the allocation to Passthrough and IP to DHCP-Dynamic. Next, go to Home Network > Wi-Fi > Advanced Settings and turn off the 2.4 and 5.0 Wi-Fi bands. Next, unplug the modem, factory reset the mesh system, use Ethernet port one on the modem to connect to the mesh system, power everything on, and follow the setup process.
A single Samsung SmartThings hub covers up to 1,500 square feet. You can add up to 32 hubs for additional coverage.
In most cases, Double Network Address Translation (Double NAT) does not affect Wi-Fi performance. But it can be an issue if you play online games or use port forwarding rules and Universal Plug and Play (UPnP). Learn more about Double NAT.
If Double NAT causes problems, you have a few options:
If this router is independent of your modem, power off and unplug this router and directly connect your modem to your Google Nest Wifi router or primary Google Wifi point.
If this router is combined with your modem, enable bridge mode on your modem/router combo. This will take care of the potential Double NAT issue.
- Connect a computer directly to your router with an Ethernet cable.
- Log into your router or modem/router combo and find its settings to enable bridge mode.
- To access your router’s settings, you might have to open an internet browser and enter your router’s IP address in the address bar like this:
Steps will vary depending on the device. Many Internet Service Providers (ISP) and manufacturers provide instructions on how to do this. To learn how to turn on bridge mode, check your ISP’s support website.
A single Google Wifi point or Google Nest Wifi router that is not part of a mesh system can be set to bridge mode. Bridge mode disables the DHCP and routing functions so double NAT is no longer an issue. In bridge mode, this single mesh point will operate as a pure Wi-Fi access point connected over an Ethernet wire to the primary modem/router.
Note: Bridge mode will only work if you’re using a single Nest Wifi router or Google Wifi point. If you’re creating a mesh network with multiple Wifi devices, your Nest Wifi router or primary Wifi point cannot be in bridge mode.
This is because the Nest Wifi router or primary Wifi point needs to control settings and communication within your Wi-Fi network. If it’s in bridge mode, in addition to losing mesh capability, you’ll also lose some of Google Nest Wifi or Google Wifi’s functionality:
will be unavailable. can’t be edited. settings can’t be edited. will be unavailable.
Wi-Fi speed results in Network check will be unavailable (but download and upload results will still work).
Additionally, bridge mode disables many of Google Wifi and Google Nest Wifi’s security protections. This is because your upstream router (the modem/router combo in the above scenario) is the one performing DNS steering, packet inspection, executable patching, etc.
Google Wifi and Google Nest Wifi’s automatic security updates maximizes your privacy and security. These protective features are most effective, and in some cases, only effective, when all traffic passes through your Nest Wifi router or primary Google Wifi point (instead of through another router).
If you have a third-party router, you can wire a Nest Wifi router or primary Google Wifi point to it, then mesh additional Wifi points downstream.
If you still want to turn your Nest Wifi router or primary Wifi point into a bridge, you can follow the steps below:
- Open the Google Home app .
- Tap Wi-Fi Settings Advanced Networking.
- Tap Network mode your Wifi router or point Bridge mode.
- Tap Save .
You can connect 2 routers to extend the Wi-Fi coverage in your home. But when you have 2 routers, each with their own private Wi-Fi network, your personal devices can have a hard time communicating with each other. This scenario is called Double NAT.
For example, let’s say you want to wirelessly print a picture from your computer. If you have 2 Wi-Fi networks, it’s possible that your computer is on one network while your printer is on the other. And if both networks are private, your computer won’t be able to tell your printer to print the picture.
This can also result in performance issues if you play online games or use port forwarding rules and UPnP.
To fix this, bridge mode lets multiple routers share one single Wi-Fi network. Here’s what that could look like:
Double NAT isn’t necessarily a problem. For most people, Double NAT does not affect Wi-Fi performance. But it can be an issue if you play online games or use IP address assignments, port forwarding rules, and UPnP.
Best answer: It doesn’t have to. Eero is meant to replace your existing router, so the two don’t need to work together. For certain circumstances, like if you have a modem and router combo device, if you want to continue using your router’s network management settings or if your ISP requires specific equipment, you can use Eero in conjunction with any wireless router with a few simple configurations.
- Mesh networking: Eero Home Wi-Fi System (From $299 at Amazon)
Eero as a router replacement
Eero is a mesh Wi-Fi system made up of the main Eero hub and Beacons that you place throughout your house. This works better than a traditional router setup because it broadcasts the Wi-Fi signal from multiple points, eliminating dead zones and perking up speeds at the edges of your network. Eero in particular is super user-friendly and has an appealing, minimalist design. It also has routing and network management capabilities that you control from the Eero app, so you can completely and easily replace your router with the Eero Home Wi-Fi System. To do that, simply disconnect your standalone router, plug the main Eero hub into your cable or DSL modem and set it up following the in-app instructions.
Modem and router combos
Internet service providers (ISPs) frequently rent out modem and router combination gateways to subscribers. If you only have one device between your main internet connection and the rest of your network, it’s probably a modem/router. Because the two functions take place in the same machine, you can’t just replace the whole thing with Eero. You absolutely can use Eero with a modem/router, but setting it up requires a few extra steps to make sure everything runs smoothly.
In most cases, you should first set up your Eero system normally by plugging the main hub into the modem/router via Ethernet and then following the in-app instructions. Once this is done, turn off the combo device’s routing and Wi-Fi functions by placing it into bridge mode. Specific instructions how to do this vary by device and are available on your ISP’s website, but generally, the process is as easy as accessing the router’s web interface and toggling on the bridge setting.
If you don’t put the router into bridge mode, you could end up with two separate Wi-Fi networks that don’t communicate very well. This is also known as double NATing. Most of the time this happens by accident, and it often doesn’t interfere with normal internet usage. It can cause problems, however, with activities such as online gaming or remote desktop access.
Eero Bridge Mode
Like your current router’s settings and controls? Great! You can keep them by bridging your Eero. In this setup, the Eero components disperse Wi-Fi and relay information as usual, but everything is controlled by your router’s settings instead of the Eero app. Bridging Eero disables most of its features, including family profiles, Eero Plus and device bandwidth monitoring, but you still get mesh coverage and speeds. Some internet service providers require equipment that supports PPPoE or that has a specific MAC address. In these instances, you have to bridge your Eero so your network is supported by the proper system.
Our Call Center is experiencing a high number of calls due to the COVID-19 situation. We are working to assist everyone who contacts us. In the meantime, please visit www.arris.com/selfhelp for most frequently asked questions about your device. We apologize for the inconvenience and will assist you soon.
ARRIS Consumer Care
By default, the TG862 operates as a gateway, and provides Internet access for multiple devices connecting to the TG862 gateway. When operating as a gateway, the TG862 serves as a modem and a router and keeps the devices in the Local Area Network (LAN) hidden. In certain situations, it may be desired to disable the router function of the TG862, and have it operate as a modem only. This can be accomplished by configuring the TG862 for Bridge Mode. When Bridge Mode is enabled, the router function is turned off and the device directly connected to the TG862 will receive the Public IP address from the Cable Provider. This document describes how to enable and disable Bridge Mode.
NOTE 1: Although the TG862 does not route traffic when Bridge Mode is enabled, it can still act as a firewall if the firewall settings in the TG862 are enabled.
NOTE 2: The Bridge Mode feature is not included with units that have been leased or purchased from Shaw communications.
- Adding a firewall, router or another NAT device to manage the Local Area Network
- Hosting services or applications that can benefit from being directly accessible from the Internet
To Enable Bridge Mode
- Launch a web browser, such as Internet Explorer, Firefox, or Safari. Enter http://192.168.0.1 into the address box, and press the Enter key. The Login page appears.
To take the device out of bridge mode, follow the steps in reverse, or simply factory default the gateway. To log back into the gateway after it's configured in a bridge mode, manually configure an IP address of 192.168.0.2 and log into 192.168.0.1 for web interface access.
For instructions on how to manually configure an IP address in the client(s), please refer to:
Be certain to have all of the account information available before setting the gateway back to factory default. Refer to Answer # 8805 – TG862G/NA: Factory Reset.